Blind Transfer: by selecting this item, the default behavior of the phone will be to initiate a blind transfer to the number entered after pressing the SW Transfer key. Use the following settings: DTMF Type: RFC2833įEATURES -> TRANSFER In this section it is possible to configure the behavior of the telephone when the SW Transfer key is pressed during a call in mode by modifying its default value. ACCOUNT -> CODEC In this section it is important to ensure that at least the PCMA codec (G.711) is present.įor the rest, it is good to organize the list of codecs in decreasing quality and, therefore, increasing in terms of bandwidth usage optimization.ĪCCOUNT -> ADVANCED In this section you can configure how the phone sends DTMF tones. If the registration was successful, you will see Registered at the top. Server Expires: recommended value between 60 and 120 (in seconds)ġ Attention: the domain name must be entered in the xxxxxxxx.yyyy format (eg: miazienda.pbx,, società.it, etc.).įor VOIspeed 4, enter the IP address of the VOIspeed server.Īfter completing the entry of the above parameters, you need to click on the Confirm button. Server Host: Server Host: domain of the VOIspeed PBX (e.g. Connect to the Configuration → Company menu and see the value of the SIP Port parameter in the Properties box. Therefore the fields in question will be according to the cases, therefore it is necessary to consult in the settings of the PBX which is your port. NOTE: The SIP listening port in UCloud environment for SIP terminals is different for each company. – XXXX for the UCloud T46G account platform Indicate: – 5060 for the On Premises platform Port: is the SIP listening port of the PBX. Outbound Proxy Server: IP address of the VOIspeed PBX (ex: 192.168.0.220) Password: user password on the VOIspeed PBX (eg. User Name: user’s extension on the VOIspeed PBX (eg. Register Name: username of the user on the VOIspeed PBX (ex: 399) Label: Your Name (indifferent for registration purposes)ĭisplay Name: Your Name (indifferent for registration purposes) We list below the parameters to be modified Line Active: Enabled VOIspeed server domain: your_ ACCOUNT -> REGISTER Below we indicate the parameters to be modified with respect to the default configuration, referring to a generic VOIspeed PBX user with the following example credentials: Once connected via the web, the administrator’s username and default password are both set to “admin”. Obtain the phone’s IP from the DHCP server monitoring or directly from the phone, by pressing the Menu softkey (bottom right below the display) and accessing the Status section. PHONE CONFIGURATIONĬonfiguration is done via the web, by connecting with a browser to the phone’s IP address. For the use of phones with the VOIspeed Server, the Firmware version 28.72.0.25 is recommended. The Yealink T46G IP phone with default settings automatically searches for a DHCP server on the network during boot to obtain a valid IP address. It ranges from -300 to 300, the default value is 60.It is advisable to configure the Yealink T46G IP Phone always using the self-provisioning function because it is faster and absolutely error-free. The value format is the same to the start time. #For example, the value 1/4/2/5 means the start time is at 5 o'clock on Tuesday of the 4th week in January. #If the DST type is configured as By Week, the value format is Month/Day of Week/Day of Week Last in Month/Hour of Day. For example, the value 5/20/10 means the start time is at 10:00 on May 20. #If the DST type is configured as By Date, the value format is Month/Day/Hour. #Configure the DST type when the DST feature is enabled 0-By Date (default), 1-By Week #Configure the daylight saving time feature 0-Disabled, 1-Enabled, 2-Automatic (default) #Configure the update interval (in seconds) when using the NTP server. #Configure the domain name or the IP address of the NTP server. Currently this is only available via the GUI. I am looking for the configuration file that will allow me to choose a time zone so the phone will display the correct time. Using T46G behind Broadsoft firmware version 28.71.193.8.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |